Stoner 63 or XM22/E1 Assault Rifle

0 comments

Stoner 63
The Stoner 63 or XM22/E1 assault rifle, is an American modular weapons system designed by Eugene Stoner in the early 1960s. It was produced by Cadillac Gage and used in very limited numbers in Vietnam by members of the United States Navy SEALs and several law enforcement agencies.

Operating mechanism

The Stoner 63 series of weapons are gas-operated, air-cooled belt or magazine-fed and fire from the open bolt position to prevent cook-offs and enhance cooling. The weapon has a rotary bolt locking mechanism with 7 radially symmetrical locking lugs that engage a series of recesses in the barrel extension, and is actuated by a conventional long-stroke piston. The radial arrangement of locking lugs distributes the firing load evenly around the bolt head and barrel socket, reducing stress and increasing the longevity of these critical components. Attached to the piston extension is the bolt carrier which is equipped with a curved cam track that guides the bolt's cam pin (retained by the firing pin) and rotates the bolt 22.5° during the movement of the piston to either lock or unlock the bolt from behind the abutments in the barrel socket. Incorporated into the bolt carrier/piston group is an anti-bounce device, consisting of a 4 in (101.6 mm) carbide rod that rides within the piston extension’s hollow interior and moves back and forth during the recoil and counter-recoil cycles, reducing bolt bounce and preventing the possibility of firing out of battery during closed bolt firing (in the Rifle/Carbine models).

When fired, propellant gases from the ignited cartridge following the projectile down the bore are vented through a gas port into a gas cylinder where they drive the piston and bolt carrier rearward. There is about 0.2 in (5.1 mm) of uninterrupted free travel calculated to permit the gas build-up in the bore to drop to a safe level before the carrier's cam slot rotates the bolt counter-clockwise to unlock. The locking lugs have no pitch therefore no primary extraction occurs during the unlocking sequence. A deeply-seated spring-loaded claw extractor in the bolt head extracts the spent cartridge casing from the chamber and a spring-powered ejector fixed to the front feed mechanism trigger housing ejects the casing. The bolt carrier continues to the rear and compresses the recoil spring on its guide rod.

The Stoner 63 has a unique buffering system contained within the bolt carrier. In front of the carrier cap are a steel shim and a set of 27 saucer-shaped Belleville washers oriented in opposing sets of three, which absorb energy from the piston stroke by deforming into a flat plate when the bolt carrier strikes the receiver’s end cap. When the plates return to their original shape they release a pulse of strain energy which propels the reciprocating parts forward in counter-recoil with a speed only slightly below that of the original recoil velocity. This feature was designed to extend the weapon’s service life, and the plates will function without failure for between 40,000 and 50,000 rounds (depending upon the type of ammunition used and cyclic rates employed).

Feeding

In the belt-fed configuration, belt movement is produced by a roller riding in the channeled feed arm and is actuated by the reciprocating movement of the bolt. The spring-loaded feed arm is protected by a hinged top cover and is pivoted at its rear end. As the bolt travels back, the front end of the feed arm moves across the feed tray and operates a lever attached to a single set of spring-loaded pawls. These pawls move a cartridge and link over the feed tray’s stop pawl from where they are positioned onto the slotted feed path and held firmly in place by a spring-powered steel plate in the top cover. The cartridge is then pushed out of its link and the empty link is discarded through the link ejection port which is held closed by a spring-loaded dust cover.

The Stoner 63/63A is chambered for the now-standard 5.56x45mm intermediate rifle cartridge. When in the belt-fed role, the weapon would feed from a disintegrating metallic linked belt marked "S-63 BRW" which is a scaled-down version of the U.S. M13 link developed for the M60 GPMG. The Stoner 63/63A will not work reliably with the later M27 link developed for the M249 SAW. The belt is normally contained in a 150-round plastic ribbed container that has a tab allowing it to be clipped on to the side of the left-hand feed tray. Early ammunition boxes were olive drab in color and manufactured at Costa Mesa, this later changed to a black-colored plastic container made in Warren, Michigan. Stoner 63A boxes were also black but had a reduced capacity of 100 rounds as the larger container would unbalance the rifle. These can either be attached to the left-hand feed tray or held in a bottom box carrier when using the right-hand feed mechanism. Several drum-type belt carriers were designed for the left-hand feed system, with a 150-round drum container being the most popular and used frequently by SEALS in Vietnam. A 250-round drum carrier was also developed by NAWS China Lake, but this proved too heavy and cumbersome. SEALS would also resort to converting RPD belt carriers for use with their Stoners. The detachable magazines used in the Rifle, Carbine and Automatic Rifle models are fabricated from steel and weigh 8 oz (230 g) unloaded. In an effort to reduce weight, aluminum magazines were later developed cutting the weight down to 4 oz (110 g). Standard magazines have a 30-round cartridge capacity but a 20-round magazine was also offered.

Barrel

Barrel interchangeability is one of the main features that provides the Stoner 63 platform its outstanding versatility. There are 5 barrel options available for the system: the Rifle, Carbine, Automatic Rifle (AR) and two types of machine gun barrels, a standard heavy barrel and a short Commando tube. The standard machine gun and AR barrels are 20 in (508.0 mm) in length (not including the flash suppressor). The Commando barrel has a length of 15.7 in (398.8 mm) and is fluted to reduce weight and enhance the barrel's cooling characteristics. This version was sometimes used by the Navy SEALS but was never fully reliable as the gas port is near the muzzle and as soon as the bullet leaves the barrel, gas pressures drop drastically leaving the operating system little to no power reserve. The gas port was drilled larger in an attempt to alleviate this problem; however this had the effect of merely accelerating the piston's initial displacement. The issue was never truly resolved. The Rifle, Carbine and AR barrels have no gas valves as they are exclusively used in magazine-fed configurations and do not require the energy surplus levels of belt-fed mechanisms. The standard machine gun barrel has a manually adjustable gas regulator that can be operated by inserting the nose of a cartridge into a hole over the regulator’s lock detent, pushing down on the detent and rotating to the desired position. The gas regulator has three settings: a "slow" cyclic rate of about 700 rounds/min, produced when the narrowest indicator notch is set over the detent; a middle position with an intermediate rate of 830 rounds/min and a third "fouled" position that delivers the largest quantity of propellant gas to the system, resulting in a rate of fire of 865 rounds/min (the use of this setting should be limited as it induces excessive wear on the operating mechanism).

All Stoner 63/63A barrels are gas nitrided and have a quick-detach capability and can be removed in a matter of seconds in field conditions by simply pushing down a latch located on top of the weapon in front of the feed cover and pulling the barrel forward (with the bolt retracted). The chamber portion of the barrel rests on a U-shaped barrel bracket attached to the gas cylinder. The barrel is firmly locked in position by means of a spring-loaded latch (with two nested coil springs) which drives a steel pin into a hole in the barrel socket. All barrels have a gas block to which a bayonet lug and front sight assembly are mounted. The barrels are equipped with a bird cage type flash suppressor with six oval ports. The AR and standard machine gun barrels also have a carrying handle that can be snapped into one of three positions or removed altogether. The black-painted wooden handles are attached to a steel rod via roll pin. With a few exceptions, all the barrels used in the Stoner 63/63A have a six-groove right-hand rifling with a twist rate of 1:12 in (305 mm), designed to stabilize the lightweight 55-grain M193 projectile (standard at the time). However, after NWM had obtained a license to produce the Stoner 63A, some barrels were manufactured with a 1:8 (200 mm) in rifling pitch to be used with heavier experimental bullets. None of these were ever produced in significant numbers.

Fire control

The Stoner 63/63A LMG is an automatic weapon that fires from the open bolt and the trigger mechanism permits only fully automatic firing though burst size can be controlled by the shooter. The entire trigger unit has four trigger pins that give the unit its modularity. The front pin holds a flapper-type magazine catch/release (used in the Rifle/Carbine variants and the left-hand feed LMG with a 150-round drum-type belt container), a full dust cover (used with the top-feeding Automatic Rifle or vertically mounted ammo box on any belt-fed system) or a half size dust cover (used with the right-hand-feed bottom box carrier). The next two pins retain the timer and hammer, both of which are absent in the open bolt configurations. The final pin acts as the trigger’s axis shaft; the spring-loaded sear pivots on the selector lever’s axis pin. The selector is disconnected when firing from the open bolt and a sliding manual safety installed near the trigger guard disables the trigger when pushed to the rear. The rear portion of the trigger housing serves as a receiver end cap and is used to attach the shoulder stock. The black polycarbonate pistol grip is also attached to the trigger housing. The checkered grip is flared at the bottom to prevent the shooter’s hand from sliding off and has an internal storage compartment sealed by a hinged cover with a spring-loaded hatch.

Features

The hooked, non-reciprocating steel charging handle is typically mounted on the right side of the receiver. It has 24 lightening holes and engages a projection on the piston to draw the piston and bolt group to the rear (cocked) position. The handle should then be pushed back forward allowing a flat-spring latch riveted to the front end to capture a slotted plate welded to the front of the receiver. With the right-hand feed mechanism with underslung box carrier installed the handle is awkward to operate, so a special slotted forearm with a bottom cocking handle was developed.

The nucleus of the Stoner 63 system is the receiver which is a rectangular sheet metal pressing. The gas cylinder, support structures, brackets, lugs and other devices are welded in place. The front portion carries the piston and barrel and is perforated to reduce weight and improve air circulation around the barrel and gas cylinder. The rear segment holds the piston extension and bolt group. The ejection port is on the right side when the receiver is inverted and the weapon is configured as a rifle or carbine and on the left side when in the various machine gun roles. The various components are phosphate finished and then coated with a black baked enamel finish called Endurion. Early examples of the Stoner 63 were delivered with all wood furniture, however these were soon replaced with black polycarbonate parts with the exception of the handguard, which remained wood, but was painted black.

The Stoner 63 bipod is a non-locking type that attaches to the gas tube; it does not pivot and has a limited height adjustment feature. The Stoner 63A bipod is extensively perforated with lightening holes and can be locked in either the stowed or deployed positions. It too does not pivot but is compatible with the earlier Stoner 63, whereas the Stoner 63 bipod will not work with the later 63A pattern guns as the gas tube is of a larger diameter.

Sights

The sight arrangement on the Stoner 63/63A differs amongst the various configurations. On the belt-fed LMGs, the rear sights are mounted on the top cover. These consist of a folding leaf aperture elevation scale graduated in 100 m increments from 200 to 1,000 m. The rear sight can also be corrected for windage in ¼-mil increments. When the primary sight is folded down, a battle sight aperture with a diameter of 0.09 in (2.29 mm) is exposed. The Rifle and Carbine versions have simple flip-type apertures with settings for 0–300 and 300–500 m contained between large perforated protective ears. The sights are adjustable in both windage and elevation in 1 MOA increments. All variants share the same front sight assembly—a semi-shrouded round threaded post adjustable for windage and elevation zero (similar to the M16 front sight).

Accessories

The Stoner 63/63A is supplied with several accessories, including: a blank-firing attachment (BFA), winter trigger guard, asbestos-lined spare barrel bag, cleaning kit, 40 mm grenade launcher, several types of slings and a wide range of belt box and magazine pouches.

The Stoner 63/63A used three different types of bayonets: the standard U.S. M7, the KCB 70, developed specifically for this rifle by the West German company Eickhorn-Solingen together with NWM and a rare bayonet made by the Swiss industrial conglomerate SIG. The KCB 70 features a 7-inch (180 mm) long Bowie blade with a clip-point and an integrated wire-cutter, it was inspired by Soviet bayonets for the AKM. A highly successful multi-purpose tool that was a far superior field knife to the M7, it evolved into the KCB 77, a modular design that was adapted to many different assault rifles.

Variants

The Stoner 63 was produced in several configurations, with 15 separate assemblies, which had limited parts commonality. These variants included a carbine, an assault rifle, and various light machine guns feeding linked ammunition from the left or right. The gas system was mounted in different positions depending on the weapon's configuration. Due to the multi-role nature of the design the carbine and rifle versions were heavier than comparable weapons of the same type.

  • Stoner 63/63A Rifle: A standard assault rifle fed from below by a 30-round box magazine. Spent cases are ejected to the right. The cocking handle and gas system are mounted above the barrel. Unlike the belt-fed configurations, the Rifle fires from closed bolt. The rifle configuration was field tested by the USMC for a short period during 1967. It was eventually fitted with a lightweight bipod that folded beneath the handguard.
  • Stoner 63/63A Carbine: The Carbine is similar to the Rifle configuration, but with a shorter barrel and a folding shoulder stock. The carbine configuration was field tested by the USMC for a short period during 1967.
  • Stoner 63/63A Automatic Rifle: The Automatic Rifle is a closed-bolt rifle fed from a top-mounted, 30-round magazine. The front and rear sights are offset to the left to compensate for the magazine's position. The AR does not have a semi-automatic mode. The automatic rifle configuration was field tested by the USMC for a short period during 1967.
  • Stoner 63/63A Light Machine Gun: The LMG configuration fires from an open bolt and is fed from the right-hand side by linked ammunition contained in a 100-round plastic box. The receiver is identical to the Rifle variants, but is inverted, so that spent cases and links are ejected to the left. The LMG has a quick-change barrel and the gas cylinder is positioned below the barrel since the receiver is inverted. The LMG configuration was adopted for military use by Navy SEAL units operating in Southeast Asia.
  • Stoner 63/63A Medium Machine Gun: Identical to the LMG configuration. The difference is that the MMG comes with a separate adapter than can be used to attach the weapon to an M2 or M122 tripod.
  • Stoner 63/63A Fixed Machine Gun: Internally identical to the LMG configuration. Externally, the front sights, rear sights, foregrip and pistol grip are all removed. The trigger is activated remotely by a 24V solenoid. The FMG was designed for use with the Cadillac Gage Commando APC, but was never officially adopted.
  • Stoner 63/63A Commando: The Commando is a derivative of the LMG configuration. It is fed from the right by a 100-round drum magazine clipped below the receiver. The cocking handle is mounted underneath the foregrip for easier access. To save weight, the Commando eschews the quick-change barrel found on the other belt-fed configurations. This variant was used by some United States Navy SEAL units in Vietnam.
  • Stoner 63 Survival Rifle: The Survival Rifle was designed in 1964 to compete with the Colt Model 608 as an aircrew self-defense weapon. It is mechanically similar to the Rifle configuration, but has several external modifications made to fit into United States Air Force size constraints. These include a cut-down pistol grip, an absent handguard, shortened barrel and receiver, and a top-mounted cocking handle. The Survival Rifle does not incorporate the 63A upgrades. Only one prototype was ever produced—it survives to this day.

The most recent descendant of this line is the Stoner LMG produced by Knight's Armament Company, which has significant changes from the older Stoner 63.

Robinson Armament Co. also produces the semi-automatic M96 Expeditionary Weapon System which, though technically different, was based on the Stoner 63 design, and thus has some of its features and configurations.

Stoner 63
Type Light machine gun / assault rifle
Place of origin United States
Service history
Used by United States Navy SEALs, United States Marine Corps (trials only)
Wars Vietnam War, Invasion of Grenada
Production history
Designer Eugene Stoner, L. James Sullivan, Robert Fremont
Designed 1961–1963
Manufacturer Cadillac Gage, NWM De Kruithoorn N.V. (prototypes only)
Produced 1963–1971
Number built Approx. 4,000 (both versions)
Specifications
Weight LMG, MMG: 11.68 lb (5.3 kg)
FMG: 10.31 lb (4.68 kg)
Commando: 10.50 lb (4.76 kg)
AR: 10.19 lb (4.62 kg)
Carbine: 7.90 lb (3.58 kg)
Rifle: 7.75 lb (3.52 kg)
Length LMG, MMG, AR, Rifle: 40.25 in (1,022 mm)
Carbine: 36.68 in (931.7 mm) stock extended / 26.60 in (675.6 mm) stock collapsed
Commando: 35.95 in (913.1 mm)
FMG: 30.38 in (771.7 mm)
Barrel length LMG, MMG, FMG, AR, Rifle: 20 in (508.0 mm)
Carbine, Commando: 15.7 in (398.8 mm)
Width 5.31 kg empty

Cartridge 5.56x45mm NATO
Action Gas-operated, rotating bolt
Rate of fire LMG, MMG, FMG: 700–1,000 rounds/min
AR, Rifle, Carbine, Commando: 700–900 rounds/min
Muzzle velocity LMG, MMG, FMG, AR, Rifle: 3,250 ft/s (991 m/s)
Carbine, Commando: 3,050 ft/s (929.6 m/s)
Effective range 200–1,000 m
Maximum range 2,653 m
Feed system LMG, MMG, FMG: Disintegrating link belt
AR, Rifle, Carbine, Commando: 20 or 30-round detachable box magazine
Sights Iron sights

Share this article :
 
Copyright © 2011. Military Weapons|Firearms|Tank|Jet Fighter|Battleship - All Rights Reserved
RSS Feeds
Powered by Military Weapons